Simple Software
Maintenance
Training
Troubleshooting
- Cutting Issues
- Optimising
- Printer
- AIT
- OFK
- Error Codes
  - Errors 0-9
    - Error 0
    - Error 1
    - Error 2
    - Error 3
    - Error 4
    - Error 5
    - Error 6
    - Error 7
    - Error 8
    - Error 9
  - Errors 10-19
    - Error 10
    - Error 11
    - Error 12
    - Error 13
    - Error 14
    - Error 15
    - Error 16
    - Error 17
    - Error 18
    - Error 19
  - Errors 20-29
    - Error 20
    - Error 21
    - Error 22
    - Error 23
    - Error 24
    - Error 25
    - Error 27
    - Error 28
    - Error 29
  - Errors 30-39
    - Error 30
    - Error 31
    - Error 32
    - Error 34
    - Error 36
    - Error 37
    - Error 38
    - Error 39
  - Errors 40-49
    - Error 40
    - Error 42
    - Error 43
    - Error 44
    - Error 45
    - Error 46
    - Error 47
    - Error 48
    - Error 49
  - Errors 50-59
    - Error 51
    - Error 52
    - Error 53
    - Error 54
    - Error 55
    - Error 56
    - Error 57
    - Error 58
    - Error 59
  - Errors 60-69
    - Error 61
    - Error 62
    - Error 63
    - Error 64
    - Error 65
    - Error 66
    - Error 67
    - Error 69
  - Errors 70-79
    - Error 70
    - Error 71
    - Error 72
    - Error 73
    - Error 74
    - Error 75
    - Error 76
    - Error 77
    - Error 78
    - Error 79
  - Errors 80-89
    - Error 80
    - Error 81
    - Error 82
    - Error 83
    - Error 84
    - Error 85
    - Error 86
    - Error 87
    - Error 88
    - Error 89
  - Errors 90-99
    - Error 90
    - Error 91
    - Error 92
    - Error 93
    - Error 94
    - Error 95
    - Error 96
    - Error 97
    - Error 98
    - Error 99
  - Errors 100-109
    - Error 100
    - Error 101
    - Error 102
    - Error 103
    - Error 104
    - Error 105
    - Error 106
    - Error 107

All Files

Isolation Procedures
- Electrical Isolation
- Pneumatic Isolation

You are here: Maintenance > Isolation Procedures > Electrical Isolation

Isolation procedures

Note: the isolation procedures below are to be followed when required by a maintenance operation.

Electrical isolation

Saw

Save any open files and close Simple.
Shut down the PC (Start Menu > Shut down).
Hold down the red STOP button on the operator console for 3 seconds.
Press the E‑stop button on the operator console.
Remove all timber from the saw.

Note: make sure the PC is now completely off and the monitor is blank before continuing.
Turn off the electrical isolation switch on the front of the saw.
Lock out / tag out the electrical isolation switch.

Dust Extractor (if required)

Press the red STOP button on the dust extractor control panel.
Press the E‑stop button on the dust extractor control panel.
Isolate the incoming power supply to the dust extractor.
Lock out / tag out the incoming power supply to the dust extractor.

Pneumatic isolation

Turn off the pneumatic isolation switch on the pneumatic unit.
Lock out / tag out the pneumatic isolation switch.